# Glossaries: No output [closed]

The code compiles but no output for Glossaries. I don't see any error message. I checked .glo file. It is empty. The code is here in short

\documentclass[12pt]{report}

\usepackage{dcolumn}% Align table columns on decimal point
\usepackage{bm}% bold math
\usepackage{MnSymbol}
\usepackage{html}
\usepackage{url}
\usepackage[none,dcucite,abbr]{harvard}
\usepackage{graphicx}
\usepackage{amsmath}
\usepackage{uathesis}
\usepackage{lscape}
\usepackage{longtable}
\usepackage{cite}
\usepackage{epsfig}
\usepackage{upgreek}
\usepackage[textwidth=13cm,textheight=20cm]{geometry}

\usepackage{glossaries}
\makeglossaries
\newglossaryentry{electrolyte}{name=electrolyte,description={solution able to conduct electric current}}

\newtheorem{theorem}{Theorem}
\newtheorem{acknowledgement}[theorem]{Acknowledgement}
\newtheorem{algorithm}[theorem]{Algorithm}
\newtheorem{axiom}[theorem]{Axiom}
\newtheorem{case}[theorem]{Case}
\newtheorem{claim}[theorem]{Claim}
\newtheorem{conclusion}[theorem]{Conclusion}
\newtheorem{condition}[theorem]{Condition}
\newtheorem{conjecture}[theorem]{Conjecture}
\newtheorem{corollary}[theorem]{Corollary}
\newtheorem{criterion}[theorem]{Criterion}
\newtheorem{definition}[theorem]{Definition}
\newtheorem{example}[theorem]{Example}
\newtheorem{exercise}[theorem]{Exercise}
\newtheorem{lemma}[theorem]{Lemma}
\newtheorem{notation}[theorem]{Notation}
\newtheorem{problem}[theorem]{Problem}
\newtheorem{proposition}[theorem]{Proposition}
\newtheorem{remark}[theorem]{Remark}
\newtheorem{solution}[theorem]{Solution}
\newtheorem{summary}[theorem]{Summary}
\newenvironment{proof}[1][Proof]{\textbf{#1.} }{\ \rule{0.5em}{0.5em}}
\begin{document}
clearpage
\tableofcontents
\clearpage
\listoffigures
\clearpage
\listoftables
\clearpage
\printglossaries
\bodyoftext

\chapter{Introduction}
\bibliographystyle{unsrt}
\bibliography{abc}
\bigskip
\end{document}

-
Welcome to TeX.SX! Declaring a glossary entry is not sufficient; you have to use a \gls command for making it into the glossary. Note that html is a very obsolete package and it's not compatible with hyperref, as far as I know; load hyperref later. –  egreg Aug 27 at 21:31
Could you please let me know how/where to use \gls command! I am using WinEdt 6.0. Thanks in advance. –  Shyama Aug 27 at 21:33
I had to use hyperref and had to place it in the beginning as my figure captions were long and went out of the right margin. –  Shyama Aug 27 at 21:40
I used \Gls{electrolyte} after \printglossaries but no output again! Although now the .glo file contains this \glossaryentry{electrolyte?\glossaryentryfield{electrolyte}{\glsnamefont{electro‌​lyte}}{solution able to conduct electric current}{\relax }|setentrycounter{page}\glsnumberformat}{14} –  Shyama Aug 27 at 21:49
This question appears to be off-topic because it is about a problem due to outdate (or missing) software –  egreg Dec 7 at 23:08