# Latex commands for a specific page format [closed]

I am writing a report for which my University has given the following guidelines (Clearly, it was intended for use with Microsoft Windows).

• Project reports should be typed only on one side of the paper with 1.5 or double line spacing on a A4 size bond paper (210 x 297 mm). The margins should be: Left - 1.25", Right - 1", Top and Bottom - 0.75".
• The chapter must be left or right justified (font size 16). Followed by the title of chapter centered (font size 18), section/subsection numbers along with their headings must be left justified with section number and its heading in font size 16 and subsection and its heading in font size 14. The body or the text of the report should have font size 12.

I used the following commands in my latex file, but somehow, it didn't look like the document my friend printed using Word.

Specifically, I have the following questions:

1. Does 12pt in latex mean size 12 in Word?
2. Does \onehalfspacing mean the same as "1.5 line spacing" in word?
3. Will the following commands produce the same margins as setting the margins in Word?
4. What changes will I need to make to get the required format?

(If you are interested, the complete specification is here: http://vtu.ac.in/index.php/examination-guidlines.html?start=12)

\documentclass[a4paper, 12pt]{report}
\usepackage[top=0.75in, bottom=0.75in, left=1.25in, right=1in]{geometry}

\chapternumberfont{\fontsize{16}{17}\selectfont}
\chaptertitlefont{\fontsize{18}{19}\selectfont \centering}
\sectionfont{\fontsize{16}{18}\selectfont}
\subsectionfont{\fontsize{14}{16}\selectfont}

\onehalfspacing

\pagestyle{fancy}
\fancyhf{}

\renewcommand{\footrulewidth}{0.4pt}

\lhead{\fontsize{08}{10}\selectfont Control of A solenoid valve through current governing\\ implemented on a Renesas R8C23 microcontroller}

\rfoot{\fontsize{10}{12}\selectfont \nouppercase{\thepage}}

\lfoot{\fontsize{08}{10}\selectfont Department of Electronics and Communications Engineering,\\ K.S.I.T}


-
Welcome to tex.sx! –  N.N. Jun 7 '11 at 20:04
@Dilip: Please don't forget to accept the answer which solved our problem best. This concludes the question and assigns points to the answerer (and to you). –  Martin Scharrer Jul 29 '11 at 11:23
@Martin: I don't think we're likely to see Dilip here again; after all, I say this question should be closed because in its current form, it cannot and should not be answered. Imho this kind of bundled questions should not be promoted. –  doncherry Jul 30 '11 at 9:27

## closed as too localized by Martin Scharrer♦Jul 30 '11 at 9:34

This question is unlikely to help any future visitors; it is only relevant to a small geographic area, a specific moment in time, or an extraordinarily narrow situation that is not generally applicable to the worldwide audience of the internet. For help making this question more broadly applicable, visit the help center.If this question can be reworded to fit the rules in the help center, please edit the question.

The 12 point of Word will be PostScript point, which in TeX would be called 12bp. A TeX pt is slightly smaller: it's 1/72.27 inch, while a bp/PostScript point is 1/72 inch. See also http://en.wikipedia.org/wiki/Point_%28typography%29

You can use 12bp instead of 12 in your \fontsize commands.

-
and also a scalable font; with the default CM fonts arbitrary dimensions are not honored. Or say \usepackage[T1]{fontenc} and \usepackage{type1ec}, assuming that the OP's system has the CM-super package. –  egreg Jun 7 '11 at 22:21
Thank you! This was exactly what I needed :) –  Dilip Jun 7 '11 at 22:30
@egreg: That should be \usepackage{lmodern}. Or use XeLaTeX or LuaLaTeX. :-) –  Martin Schröder Jun 8 '11 at 17:38
lmodern might be a choice, of course. –  egreg Jun 8 '11 at 17:51

[I'm posting this as an answer because a) it partially is and b) it is too long to be a comment.]

Welcome to tex.sx! We usually have a one-question-per-post guideline (so other users who have the same question can find it), so I recommend you refine this post to several posts, one question each. If you haven't already, use the search function to see if your question has been asked before. A few ideas:

1. Looks like a great question, haven't read that before. It might be around though.
2. Look into What does 'double spacing' mean? , this might help. Basically, there doesn't seem to be a universally valid definition of what "line spacing" is.
3. Afaik, geometry is precise (and so should Word), but you could simply measure it yourself? Loading the package with the showframe option (\usepackage[showframe]{geometry}) will display lines indicating the margins.
4. Could you narrow this question down a bit as to what you find to be looking differently and what you can't figure out how to change? Adding pictures of your Word document and your TeX'ed file to compare might be helpful.

I hope this helps, I'm sure we'll be able to solve your issues.

P.S.: A general remark: If you indent lines by 4 spaces, then they are marked as a code sample. You can also highlight the code and click the "code" button (with "{}" on it). Shorter passages within a normal text line can be marked with backticks ().

Edit: In particular for the fourth question, please provide a minimal working example (MWE). Some packages seem to be missing in your current preamle, e.g. fancyhdr and setspace. This will, just like the splitting, make your question much easier to answer thus you'll eventually get better answers.

To get a sample document, you can use the blindtext package, add \usepackage{blindtext} in your preamble and as a document body

\begin{document}
\Blinddocument
\end{document}
`

This will give you a ~14 page document with all kinds of elements in it.

-
Thank you, I will try using showframe, and post my results here. Regarding the 4th point, its the line spacing that looks different. I notice that latex uses different line spacing for chapter headings, section headings etc. This doesn't happen with Word, and I guess that is making the latex document look different. And sorry about the multiple questions, my bad... –  Dilip Jun 7 '11 at 20:51