Take the 2-minute tour ×
TeX - LaTeX Stack Exchange is a question and answer site for users of TeX, LaTeX, ConTeXt, and related typesetting systems. It's 100% free, no registration required.

When I use the article class with beamer, the slides are not clearly demarcated. Rather, the slides just blend in with the document as dot points, headings, and so on. This is fine when I actually want to create a stand-alone document. However, if I'm trying to create some notes to accompany a set of slides, it would be useful to clearly indicate where a slide starts and stops.

  • What is a good strategy for clearly demarcating slide content from non-slide content using the article class with beamer?
  • For example, how could I add a box around the slide content?

Minimal example:

Here's a minimal example

\documentclass{article}   
\usepackage{beamerarticle}
\begin{document}
\begin{frame}{Frame title}
\begin{itemize}
\item A dot point
\item another dot point
\item Another dot point
\end{itemize}
\end{frame}

Some text outside the frame.   
\end{document}

Which produces the following:

enter image description here

share|improve this question

2 Answers 2

up vote 3 down vote accepted

There is a way to do this. When using a beamer file in article mode, there are still loads of templates in place, it's just that most of them do boring things. So there are templates frame begin and frame end which by default do nothing, but which we can use to separate out the frames.

Here's two possibilities, one with lines and one with a box. The lines are simpler; to get a box I have to use some TikZ-magic. I couldn't figure out a way to get the contents of the frame in to a \framebox but I could use the remember picture,overlay stuff from TikZ to put a coordinate at the start and end, and then draw a box (warning: the box is drawn after the frame so can't be used to put a background behind the frame).

delimited frames

And here's the code to get that:

\documentclass[border=10]{standalone}
%\url{http://tex.stackexchange.com/q/25259/86}
\usepackage{beamerarticle}
\usepackage{tikz}

\defbeamertemplate<article>{frame begin}{lined}{\par\noindent\rule{\textwidth}{1pt}\par}
\defbeamertemplate<article>{frame end}{lined}{\par\noindent\rule{\textwidth}{1pt}\par}

\newcounter{framebox}
\defbeamertemplate<article>{frame begin}{tikzed}{\par\noindent\stepcounter{framebox}\tikz[remember picture,overlay] \path (-1ex,0) coordinate (frame top \the\value{framebox});}
\defbeamertemplate<article>{frame end}{tikzed}{\hspace*{\fill}\tikz[remember picture,overlay] \draw (frame top \the\value{framebox}) rectangle (1ex,0);\par}


\mode<article>{
\setbeamertemplate{frame begin}[tikzed]
\setbeamertemplate{frame end}[tikzed]
}

\begin{document}
This is before the frames.
\begin{frame}
\frametitle{A Typical Frame}

\begin{block}{A Block}
With some contents
\end{block}

\structure{Some structure}

\begin{itemize}
\item A list provides
\item Organisation
\item To presentations
\end{itemize}
\end{frame}
This is between them.

\mode<article>{
\setbeamertemplate{frame begin}[lined]
\setbeamertemplate{frame end}[lined]
}

\begin{frame}
\frametitle{A Typical Frame}

\begin{block}{A Block}
With some contents
\end{block}

\structure{Some structure}

\begin{itemize}
\item A list provides
\item Organisation
\item To presentations
\end{itemize}
\end{frame}

This is after the whole lot.

\end{document}
share|improve this answer

According to the Beamer User Guide, the command \note outside of a frame creates a single note page. It is "independent" of any usage of the \note commands inside the previous frame. If you say \note inside a frame and \note right after it, two note pages are created. I presume that this is will work for the document class of article that uses the beamerarticle package, however, if you require notes to accompany your slides, you should define the document class as beamer.

share|improve this answer
    
Thanks for the help. In general I quite like just being able to add text outside of frames and letting this constitute my notes. I think I'm looking more for a way to override the default display of content in the frame environment when displayed using the article class (e.g., adding a box around it or something). –  Jeromy Anglim Aug 9 '11 at 6:39
    
Have you tried \framebox[width][position]{text}? It is exactly the same as the \makebox command, except that it puts a frame around the outside of the box that it creates. –  Bill Aug 9 '11 at 6:47

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.