{arc} is about arc drawing in {tikz} or other graphic environments, including {pstricks}

learn more… | top users | synonyms

11
votes
3answers
503 views

arc that passes from (B) having a center on (A), automatically calculates (AB) distance

I want to create an arc which automatically calculates the distance (AB). Inspired by page 58 at pgf manual. But the code block % \draw (H) ++arc (15:60: $ (A) ! - ! (B) $); does not help much. ...
8
votes
1answer
545 views

How to use curve path with fill command in tikz?

I´ve tried using arcs to get the picture below, but I have to precise a specific center for each arc, because they don´t finish in the point which they should. Instead of arcs, I want to use curve ...
8
votes
1answer
248 views

Marking a specific point on an arc

I want to draw a line from one arc to other but I do not know if it is possible to mark a point on an arc and start drawing on that point. Is it possible to draw lines like below image? ...
3
votes
1answer
5k views

Use \overarc to represent an arc

I can not understand why the following tex file does not compile. \documentclass{elsarticle} \usepackage[hmargin=1in,vmargin=1in]{geometry} \usepackage{amsmath} \usepackage{amssymb} ...
4
votes
2answers
4k views

Draw the proper angle arc

I am trying to draw an arc to indicate angle between y axis and r line, but I don't seem to achive it. My code is \documentclass[11pt,a4paper]{book} \usepackage{kerkis} %\usepackage{kmath} ...
8
votes
1answer
173 views

Arcs not being properly drawn for some special coordinates

While attempting to draw some geometry diagrams in TikZ, I was having problems drawing an arc to mark off an angle. The arc kept falling too short and would not intersect both rays of the angle. (It ...
6
votes
1answer
250 views

How to clip overlaying surfaces/paths instead of filling them with white?

The following code \newcommand*{\arcthickness}{0.3} \newcommand*{\myarc}[4]{ % x,y,radius,text % node is positioned by splitting the arc in two parts % see ...
2
votes
0answers
122 views

Draw centered label above arc in TikZ [duplicate]

Possible Duplicate: How to place a node in the middle of an arc? Following the manual where labels are positioned on curves (\draw (0,0) .. controls (6,1) and (9,1) .. node {midway} ...
4
votes
2answers
1k views

position arc relative to circle [duplicate]

Possible Duplicate: Draw arc in tikz when center of circle is specified an very trivial question but I can't do it! Sorry but I find coordinates confusing. I would like to draw an arc ...
27
votes
2answers
30k views

Drawing a TikZ arc specifying the center

The TiKz command for an arc: \draw (0,0) arc (-30:30:2) ; Draws an arc that starts at (0,0), and would be the part of the circle from -30 degrees to +30 degrees of radius 2. It is very hard to ...
7
votes
1answer
2k views

How do I draw an arc between two lines in pgfplots using axis cs

I would like to draw an arc between to lines in a pgfplots picture using axis cs. My first attempt is as follows: \documentclass[12pt,a4paper]{article} \usepackage{pgfplots} ...
11
votes
4answers
1k views

Draw an arc over 360 degrees

I have the following problem with tikz: I want to draw some circular arcs, but unfortunately these arcs have degrees which pass the 360° line. I would like to be able to draw these arcs with one ...
7
votes
3answers
3k views

How to Intersect an arc with a line without calculating the angle

I'd like to draw an optics-related figure, for which I need to draw several beams with varying opening angles, which will need to be labeled. What I've come up at the moment (boiled down to a minimal ...
30
votes
4answers
8k views

How to place a node in the middle of an arc?

I think it is a simple question, but I didn't find the answer yet. The code I'm using is the following: \draw[->](1,0) arc(0:-30:1) node[midway]{$30$}; But in this way the node is placed at the ...
18
votes
3answers
8k views

How to get correct arrow orientation on TikZ arc?

I'm trying to fix the following TikZ figure, where the circle device in the middle should be embraced by two bended arrows pointing counter-clockwise. I have drawn these arrows with an arc path, ...