Angle Quotes with English Text and English Figure and Table Labels

I use a standard package, csquotes, to handle quotes. But if I use it like in the MWE below, then in front of every table I get foreign language spelling for figure and table instead of English figure and table. Like here:

\documentclass[12pt]{article}
\usepackage{amsmath, booktabs, setspace}
\usepackage[demo]{graphicx}
\usepackage[english,russian]{babel}
\usepackage[usenames]{color}
\usepackage[top = 1in, bottom = 1in, left = 1in, right = 1in]{geometry}
\usepackage[style=russian]{csquotes}
\begin{figure}[h]
\centering
\includegraphics[scale = 0.5, angle = 0]{Test}
\caption{CAPTION GOES HERE}
\label{fig:FIGURE NAME GOES HERE}
\end{figure}
\begin{table}[h]
\centering
\begin{tabular}{|llr|}
\toprule
\multicolumn{2}{c}{A} \\
B & C & D (\$) \\ \midrule E & F & G \\ & H & I \\ J & K & L \\ \bottomrule \end{tabular} \caption{CAPTION GOES HERE} \label{tab:TABLE NAME GOES HERE} \end{table} \end{document}  If I replace \usepackage[english,russian]{babel} with \usepackage[russian, english]{babel}, then get English text for figure and label, but the correct angle quotes get replaced with << and >> which are a little too low. How do I need to configure my preamble to get English standard formatting everywhere except where csquote controls style of quotes? (I do this for my preferred readability, and an editor right now only needs to change the style in csquote to get English style quotes again.) • If you use \usepackage[demo]{graphicx}, you wont need to tell anyone to replace the figure name with their own. – dustin Aug 12 '13 at 10:52 1 Answer This is to do with which fonts are being used for output. Latex has a number of output encodings. The standard is OT1, when Russian is selected you get T2A (the log file contains a warning that you should have set this up). So if you quotes are only for parts of the text in Russian language then you can simply write:  \foreignlanguage{russian}{\enquote{....}}  assuming you have selected main language English via \usepackage[russian,english]{babel}. Here is a complete document. \documentclass[12pt]{article} \usepackage{amsmath,booktabs,setspace} \usepackage[russian,english]{babel} \usepackage[style=russian]{csquotes} \begin{document} \enquote{A quote} \foreignlanguage{russian}{\enquote{A quote}} \begin{figure}[h] \centering \rule{3cm}{2cm} \caption{Caption goes here} \label{fig:FIGURE NAME GOES HERE} \end{figure} \begin{table}[h] \centering \begin{tabular}{llr} \toprule \multicolumn{2}{c}{A} \\ B & C & D (\$) \\
\midrule
E & F & G \\
& H & I \\
J & K & L \\
\bottomrule
\end{tabular}
\caption{Caption goes here}
\label{tab:TABLE NAME GOES HERE}
\end{table}

\end{document}


On the other hand if you are just looking to use this style quote in English, you could load the (often preferable) T1 encoding:

 \usepackage[T1]{fontenc}


This gives quotes that are a lot closer to the Russian T2A ones:

\documentclass[12pt]{article}

\usepackage[russian,english]{babel}
\usepackage[T1]{fontenc}
\usepackage[style=russian]{csquotes}

\begin{document}
\enquote{A quote}
\foreignlanguage{russian}{\enquote{A quote}}
\end{document}


The advantage of turning T1 encoding on is that words with accents can now be hyphenated, see Why should I use \usepackage[T1]{fontenc}?.

• Thank you. It worked and I will us T1 from now on in preambles. I have one question: Is there any reason to \usepackage[T1]{fontenc} instead of \usepackage[T2A]{fontenc} directly? Both actually work for english. And neither will affect math mode, which uses its own fonts that support it, yes? – user34902 Aug 12 '13 at 12:31
• Yes, maths uses its own encoding schemes. Section 3 of the fontenc documentation explains that all encodings have to have standard English letters etc. in the standard positions, so this will work for English. Just remember to write caf\'e not café – Andrew Swann Aug 12 '13 at 13:21