Drawing a rectangle

Question

What is the easiest way to draw a rectangle on latex? I just need a simple rectangle for my students to enter the final answer of a question and I am hoping I don't have to learn anything fancy like Tikz.

Answer 1

You could just do something simple like this

\documentclass{article}
\newcommand\answerbox{%%
    \fbox{\rule{1in}{0pt}\rule[-0.5ex]{0pt}{4ex}}}
\pagestyle{empty}
\begin{document}

Put you answer here: \answerbox

\end{document}

which requires no use of TikZ.

A bit of an explanation.

The syntax for \rule is as follows:

\rule[<lift>]{<width>}{<height>}

I use two separate \rule commands because if I wrote something like

\rule{1in}{4ex}

I just get a solid black box defeating the purpose.

By using a negative value for <lift> I can drop the bottom of the box below the baseline.

\fbox then adds more space. These values are controlled with the following lengths

\fboxrule
\fboxsep

Generally, \fboxrule is 0.4pt and \fboxsep is 3pt, but you can adjust those values as desired.

Answer 2

Nothing fancy with tikz. It is easy (this answer is for just showing it).

\documentclass{article}
\usepackage{tikz}

\begin{document}
  Your answer: \tikz[baseline=0.6ex]\draw (0,0) rectangle (10cm,3ex);

  Your answer: \tikz[baseline=-4pt]\node[draw,minimum width=10cm,minimum height=3ex] {};
\end{document}

Answer 3

Actually, if all you want is a box for an answer, I'd say tikz might actually be the most readable (syntactically, at least) way to do this.

A box as wide as the text, 1in tall, is just:

\tikz \draw (0,0) rectangle (\linewidth, 1in);

The point (0,0) just references the current position in the text, then \linewidth gives it the right width (which will adjust if you change your margins, and then just set the height, 1in is just arbitrary.

Make sure to use \noindent before beginning the picture, as it will try to indent the drawing and that'll cause weird alignment issues.

Here's a simple MWE:

\documentclass{article}
\usepackage{tikz}
\usepackage{lipsum}

\begin{document}
    % question here
    \lipsum[1]
    \noindent\\
    \tikz \draw (0,0) rectangle (\linewidth, 1in);
\end{document}

You could also use standard \begin{tikzpicture} \end{tikzpicture} brackets like with any other environment, but I used \tikz instead because this drawing is only one line long. The draw command is one line long either way.

\documentclass{article}
\usepackage{tikz}
\usepackage{lipsum}

\begin{document}
    \lipsum[1]
    \noindent\\
    \begin{tikzpicture}
        \draw (0,0) rectangle (\linewidth, 1in);
    \end{tikzpicture}
\end{document} 

---

---

I know you asked for something other than tikz, but I felt the same way as you until I finally took the plunge recently. The water's warm, I think you'll like it too.

The biggest advantage to using tikz is being able to make a fancier answer box easily, for example, the line:

\tikz \draw[fill=green!5] (0,0) rectangle (\linewidth, -1in) node[pos=.1]{Answer Here:};

Gives you a 5% green fill and a label:

The draw option [fill=green!5] fills the path with 5% green, and node[pos=.1]{Answer Here:} makes a node (tikz's awesome placement tool) 10% of the way into the box (it measures diagonally, pos=1 would set the text at the bottom right corner).

\documentclass{article}
\usepackage{tikz}
\usepackage{lipsum}

\begin{document}
    \lipsum[1]
    \noindent\\
    \tikz \draw[fill=green!5] (0,0) rectangle (\linewidth, -1in) node[pos=.1]{Answer Here:};
\end{document}

---

Good luck!

Answer 4

This command draws a box filling the linewidth (you could adjust that, of course), and allowing you to specify how tall the box is.

It creates a box of specified height using \raisebox and then draws lines around it and specifies the width using \framebox.

It uses an optional argument, so \answerbox defaults to a height of 3\baselineskip, but you can change it with \answerbox[0.5\textwidth] or any other length.

\documentclass{article}
\newcommand{\answerbox}[1][3\baselineskip]{%
    \noindent\framebox[\linewidth]{%
        \raisebox{0pt}[0pt][#1]{}%
    }\par\medskip%
}
\begin{document}
Write your answer here:

\answerbox

Write another answer here:

\answerbox[5\baselineskip]

\end{document}