0

This question already has an answer here:

armatures

I have not put the MWE because I don't know where to start and check for packages to do the job.

marked as duplicate by Henri Menke, cfr tikz-pgf Jun 26 '17 at 22:48

This question has been asked before and already has an answer. If those answers do not fully address your question, please ask a new question.

  • I already check in the forum, it is not a duplicate I want to get help how to begin drawing this image, please get help? – Ousseynou Diagne Jun 26 '17 at 22:25
  • The linked question addresses exactly your question: where to begin and which package to use, where to look for information. Answers provide a full range of options and examples. There really isn't much point in duplicating that information here. Your question is the same general one about the options you have for drawing an image. (You've also asked similar questions before, so it seems odd that you don't know even which packages you might use. But whatever the reason, the answers to the linked question set out your options.) – cfr Jun 26 '17 at 22:52
4

If you want to use TikZ, here is a start for you:

\documentclass[12pt,a4paper]{article}
\usepackage{tikz}

\begin{document}
\begin{tikzpicture}
\draw (0,10) -- (5,10); % line between 2 points, coordinates of points in ()
\draw (0,9) -- node[above]{$A$} (5,9); % and with some text above it
\draw (0,8) -- node[below]{$B_1$} (5,8); % or below
\draw (0,7) -- node[below]{$B_1$} node[above]{$A$} (5,7); % or both
\draw[<-] (0,6) -- (5,6); % arrow at the start
\draw[->] (0,5) -- (5,5); % or at the end
\draw[<->] (0,4) -- (5,4); % or at both ends
\draw[very thick] (0,3) -- (5,3); % thick line
\draw[line width=5pt] (0,2) -- (5,2); % arbitarry line width
\draw[dashed] (0,1) -- (5,1); % dashed line
\draw[red] (0,0) -- (5,0); % colored line
\draw (6,0) rectangle (7,10); % a rectangle
\draw (8,0) -- node[left] {$C_n$} (8,10); % some text left from line
\draw (9,0) -- node[right] {$D$} (9,10); % or right of it
\draw[->] (10,0) -- (10,9) node[anchor=south west] {$X$}; % some text at the end of the line
\draw[<-,very thick] (11,1) node[anchor=north east] {$Y$} -- (11,10); % or at the start
\fill (11,5.5) circle (0.1); % a circle at a given coordinate
\node[anchor=north west] at (6,10) {$P$}; % some text near a point
\draw[densely dashed] (12,0) -- (12,3); % different styles for dashed lines
\draw[dashed] (12,3.5) -- (12,6.5);
\draw[loosely dashed] (12,7) -- (12,10);
\end{tikzpicture}
\end{document}

Ti*k*Z sampler

By combining these examples and selecting proper coordinates you can draw your picture.

TikZ uses 1cm as its unit length. You can also use lengths for the coordinates (e.g. (1mm,10pt)). For nicer arrows see chapter 16 of the pgf manual. A lot more can be done with TikZ. Just search for the commands and options in the maual.

  • Ok, thanks for giving me the opportunity to try it to myself. I am going to work on it and post my result. – Ousseynou Diagne Jun 26 '17 at 23:02

Not the answer you're looking for? Browse other questions tagged or ask your own question.