1

I'm writing a document and implementing a picture of device and it's technical data in a table in the same page. The problem which I have is that the page and the table are not in the same level which causes that title of picture is not at the same height

This is the code:

\begin{minipage}{0.5\textwidth}
\begin{figure}[H]
\centering
    \includegraphics[width=7cm, height=4cm]{gaszaehler}
    \caption{Q-loud EnrgyCam 2.0}
\end{figure}
\end{minipage}
\begin{minipage}{0.5\textwidth}
\begin{table}[H]
\centering
\scalebox{0.9}{
        \begin{tabular}{ | l | c|}
    \hline
        Stromversorgung  & DC 5 V  $\geq100$ mA   \\ \hline
        Betriebstemperatur &  -10 °  -  50 °\\ \hline
        Schutzklasse & IP64 \\ \hline
        Bussystem & M-Bus \\ \hline
        Dimensionen & 42 x 42 mm (T x H)  \\ \hline
        Sensoreinheit & Kamera Modul \\ \hline
    % &  &  &  \\  \hline
        \end{tabular}
        }
            \caption{Technische Daten der Q-loud EnrgyCam 2.0 \cite{energycam_mbus} }
\end{table}
\end{minipage}

could someone help me please to make them both in the same hight? the picture shows how the title of table and of the picture are not in the same height

  • Have a look here. – user121799 May 8 '18 at 17:47
  • it doesn't fix my problem: \begin{tabular}[b]{cr}% – AhmyOhlin May 8 '18 at 18:03
  • Sure, you need to read the question: use \savebox to measure the height of the table and use it to set the height of the graphics. – user121799 May 8 '18 at 18:06
1

OK, too long for a comment.

\documentclass{article}
\usepackage{amsmath,siunitx,graphicx,floatrow}
% from https://tex.stackexchange.com/a/6869/121799
\newfloatcommand{capbtabbox}{table}[][\FBwidth]
\begin{document}
\newsavebox{\testbox}%
\newlength{\testheight}%
\savebox{\testbox}{% from https://tex.stackexchange.com/a/66429/121799
        \begin{tabular}[b]{ | l | c|}
    \hline
        Stromversorgung  & DC \si{5\volt}  $\geq100\si{\milli\ampere}$   \\ \hline
        Betriebstemperatur &  \si{-10\degree} ---  \si{50\degree} \\ \hline
        Schutzklasse & IP64 \\ \hline
        Bussystem & M-Bus \\ \hline
        Dimensionen & 42 x 42 mm (T x H)  \\ \hline
        Sensoreinheit & Kamera Modul \\ \hline
    % &  &  &  \\  \hline
        \end{tabular}
        }%
\settoheight{\testheight}{\usebox{\testbox}}
\begin{figure}
\begin{floatrow}
\ffigbox{%
  \includegraphics[height=\testheight]{example-image-a}%
}{%
  \caption{Q-loud EnrgyCam 2.0}%
}
\capbtabbox{%
\usebox{\testbox}
}{%
  \caption{Technische Daten der Q-loud EnrgyCam 2.0 \cite{energycam_mbus} }%
}
\end{floatrow}
\end{figure}
\end{document}

enter image description here

I also used the opportunity to use siunitx to typeset the units.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.