Linked Questions

2
votes
1answer
8k views

Configure TeXnic Center with Sumatra [duplicate]

so I've been trying for a while to configure those two programs, but I just can't get it to work. I always get the error: [ForwardSearch("%bm.pdf","%Wc",%l,0,0,... Cannot execute the command. My ...
5
votes
0answers
3k views

How to double-click in PDF document to go to source code? [duplicate]

When creating a document, I usually build a DVI document because the YAP viewer has a nice feature which allows me to double-click on a word in the DVI document which then causes the source-code ...
14
votes
5answers
13k views

Configure TexnicCenter with something else than Adobe Reader X

My Adobe decided it should be version X now, and it misbehaves in so many ways. One way is that it is impossible to get it to open a pdf document from within TexnicCenter (or I missed something...) ...
2
votes
3answers
6k views

ForwardSearch: “Cannot execute the command” when using LuaLaTeX

If I try to compile with the LuaLaTeX-compiler in TeXnicCenter with the below outputprofile-settings, there showing up this error: [ForwardSearch("%bm.pdf","%Wc",%l,0,0,1)] Cannot execute the command ...
1
vote
2answers
4k views

“Cannot Execute the Command” error with sumatraPDF in TeXnicCenter

When I build the output, I can view it in pdf using sumatrapdf by pressing F5 sometimes, but most of the time I have to rebuild the output until it works. The error is: When I build the pdf, I can ...
5
votes
1answer
2k views

Sync between Adobe and Texniccenter

I am using TeXnicCenter and Adobe Acrobat Pro 11. My problem is whenever I compile my article in TeX -> PDF profile, it produces the output PDF and give me back from the first page, it does not ...
2
votes
1answer
1k views

open pdf at current page using TeXnicCenter and Adobe Reader, or should I use another setup?

Is it nowadays possible to open the compiled pdf at that position, where the last change happend, using the aforementioned TeXnicCenter and Adobe Reader? I used my favourite search engine ;) but didn'...
1
vote
1answer
1k views

Sumatra inverse search opens a new instance of Texnic Center

I have a little problem with SumatraPDF inverse search. I followed this post for configuration. When I click "view output", Sumatra shows my PDF (which is a good start), but when I click on a word in ...
1
vote
1answer
734 views

Adobe Reader makes TexNicCenter crash - Alternative Sumatra

Since today, without having changed ANYTHING to the configuration, Adobe Reader does not work correctly with TexNicCenter anymore. Any time I try to preview a document, TexNicCenter crashes. I suspect ...
1
vote
1answer
456 views

ForwardSearch suddenly not working (MikTeX + TeXnicCenter + SumatraPDF)

As I was working on my document, I found that suddenly my ForwardSearch stopped working. A MWE is very simple: \documentclass{elsarticle} \begin{document} This doesn't work. \end{document} Note that ...
2
votes
0answers
479 views

Inverse-search opens Notepad [closed]

I am using TeXnicCenter in combination with SumatraPDF and I have followed these instructions. However, the problem at my university is that I need to use a server-based version of TeXnicCenter, so ...
2
votes
0answers
433 views

TXC compiles document and opens PDF and hangs [closed]

Editor : TXC 2.0 b2 sumatra 2.3.2 I can compile the document without any errors. but after compilation, the TXC opens the sumatra and gets stuck. I have to force terminate the programs. But the PDF ...
0
votes
1answer
297 views

PDF build not updating

I just downloaded Latex on a new computer. On my old computer, I was able to preview my build outputs in Adobe...on my new computer, I can't. It locks. So I started digging a little and read that the ...