Questions tagged [stanli]

{stanli} is a package for structural analysis diagrams, based on {tikz-pgf}.

Filter by
Sorted by
Tagged with
0
votes
0answers
29 views

Drawing third, fourth and fifth degree parabolas the using “Stanli” package

In the shown MWE, a parabola is drawn using the "Stanli" package. How can I shift the peak of the curve to point "D" while maintaing the tangency of the parabola with the dashed ...
1
vote
1answer
72 views

Hatching Shear and moment diagrams using Stanli package in 2D and 3D

Regarding drawing internal force diagrams through the use of the Stanli package. The following parameters are required for 2D internal forces command: Start point End point Value at start point Value ...
1
vote
1answer
70 views

Using reference points in “Stanli”

When using "Stanli" package, inorder to draw a number of paragrams belpow each other, I set offset values. For the shown MWE, The origint point for each diagram is set as follows: \point{a-...
0
votes
1answer
76 views

“\internalforces” command in stanli package

Regarding drawing internal force diagrams through the use of the Stanli package. The following parameters are required: Start point End point Value at start point Value at end point Parabola height ...
1
vote
1answer
91 views

Structural Analysis Package

I am trying to add a label "100 lb/in" on both of the load distributions. Every time I attempted it, the labels pop up in places I did not intend them to be. I want them to be on top for the ...
0
votes
0answers
44 views

structmech Vs pst stru Vs Stanli

Which is the most suited package for structural analysis drawings and diagrams. I could find the packages structmech package / library pst stru package/library Stanli package/library Which is the ...
1
vote
1answer
94 views

How to incorporate the changes/modifications in the roller support?

The roller support produced by stanli package is very similar to that of hinged support and confusing most of the time, and hence I want to change or modify the output of the roller support, like the ...
1
vote
1answer
639 views

How to modify TikZ patterns

The Task: Draw a ground for a tank. My solution: Using TikZ patterns library (see page 171 of the TikZ & PGF manual). MWE: \documentclass{scrartcl} \usepackage{stanli}% loads TikZ, see: https://...
3
votes
1answer
170 views

Orientation of a TikZ diagram

I have designed a diagram, with the following code \documentclass{article} \usepackage{stanli} \usepackage{tikz-3dplot} \begin{document} \begin{figure} \centering \setcoords{-25}{10}[1][1....
5
votes
2answers
3k views

How to use PanDoc to derive output from LaTeX and TikZ to a DOCX file?

I have a LaTeX document with the following code which generates a picture using TiKZ. (Minimum working example here) \documentclass{article} \usepackage{amsmath,stanli} \begin{document} Analyse ...
2
votes
1answer
728 views

LaTeX stanli package. How to design a spring element?

The documentation for the stanli package can be found here: /https://mirror.hmc.edu/ctan/graphics/pgf/contrib/stanli/stanli.pdf And the documentation for the design of a spring, can be found here: ...
1
vote
1answer
196 views

TikZ: How to add an arrow tip to an arc drawn with the pic syntax?

This question continues my another. My code: \documentclass{scrartcl} \usepackage{stanli} \usetikzlibrary{ angles, quotes } \begin{document} \...
4
votes
1answer
219 views

How can one align input tex-files (written with TikZ) by a defined point?

My code: \documentclass{scrartcl} \usepackage{stanli} \usetikzlibrary{angles, quotes } \newcommand*\coordinateSystem{\draw [<->] (...
2
votes
1answer
84 views

How can one move the arc in the every pic quotes construction in TikZ?

My code: \documentclass{scrartcl} \usepackage{stanli} \usetikzlibrary{angles, quotes} \begin{document} \begin{tikzpicture} %the points \point{begin}{0}{0}; \point{end}{5}{0}; %the ...
6
votes
2answers
578 views

How to draw over an picture in TikZ?

My code: \documentclass{scrartcl} \usepackage{stanli} \begin{document} \begin{tikzpicture} %the points \point{above}{0}{5}; \point{above_middle}{0}{4}; \point{below_middle}{0}{1}; ...
2
votes
1answer
496 views

Can I represent the beam deflection curve with the stanli package?

With the stanli package one can easy and fast draw beam schemes. But I missing a possibility to draw a deflection curve of the beam. Maybe I overlooked something in the manual. Anyway, I solved it ...